Falex-MCTT-环球（香港）科技有限公司

Product information

Falex-MCTT

MCTT

Category：Industrial Tribology

Method Standard：ASTM D3702，ASTM G99

Application：Evaluation of friction, wear, and abrasion characteristics of materials, coatings, and lubricants.

Brand：FALEX

Description Feature Standard Test Methods Technical Data

The Falex MCTT is a versatile system for the evaluation of friction, wear, and abrasion characteristics of materials, coatings, and lubricants. This single system accommodates an ever-increasing number of test geometries and conditions. The FALEX MCTT allows investigations into a wide variety of materials, coatings and lubricants for wear rates, PV limits and determinations of static and dynamic coefficients of friction. The flexibility of controlled contact geometries, specimen materials, speed, pressures, temperatures, and motion make it one test apparatus that can meet many commercial and military test specifications and simulate the broadest range of field applications.

Applications:

» Research & Development

» Quality Control

» Product Qualification

» Performance Characteristics

» Material Evaluation

» Polymers

» Lubricants

» Coatings

» Surface Treatments

» Dry Films

ASTM D3702	Standard Test for Wear Rate and Coefficient of Friction in Self-Lubricated Rubbing Contact Using a Thrust washer Testing Machine
ASTM G99	Standard Test Method for Wear Testing with a Pin on Disk Apparatus
Proposed	Standard Test Method for Predicting Coefficient of Friction and Wear Properties of Hydraulic Fluids Using a Cyclic Stress Vane Apparatus

Drive System (30-3600 RPM Standard)	Computer controlled servo motor (equivalent to 2 Hp) with ± 0.5% accuracy (full scale) configured for 220 V, Single Phase, 50 or 60 cycle operation. The motor drives the upper vertical shaft while the lower vertical shaft is held stationary by the Torque Measurement System.
Drive System (options)	Pulley configurations are available for speed ranges 15 to 1800 rpm and 60 to 3600 rpm. The optional Reversible Drive provides Oscillatory Motion Control from 5° to 720° (angle of motion dependent on test speeds and loads).
Environments	Standard Systems provide fluid and test specimen initial temperature set point (ambient to 150°C) using liquid or dry environments.
Temperature Control	Standard Systems provide test table heaters (ambient to 150°C) for liquid and dry test environments. Automated Test Temperature System with computer control. User defined parameters for test temperature ramping rates, soaking times, and test cycle control. User programmable test alarms and shutdown levels. Optional Accessories expand operating temperatures from ambient to 200°C with Heater Cups and Heating and/or Cooling Recirculating systems.
Friction Measurement	The lower shaft transmits a signal through a load cell for determining torque. The Standard System includes a 0 to 100 lb. Load Cell. The Falex SoftWEAR™ records and displays the test torque data and calculates a real-time Coefficient of Friction. User programmable test alarms and abort levels. An Optional Low Range Load Cell (0 to 10 lbs.) is available for low range test torque measurements.
Wear Measurement	Dynamic Digital Wear Measurement System records and displays the real-time test system wear displacement. User programmable test alarms and abort levels.
Test Duration	Standard Systems include user defined alarms and abort levels for test time (H:MM: SS) and test cycles (shaft revolutions).
Utility Requirements	Power: 220 Volts, 60 cycle/50 cycle, single phase.
Utility Requirements	Pneumatics: 80 psig (5.5 bar) clean, dry air required for pneumatic load systems.
Space Requirements	20 in. (L) x 28 in. (D) x 36 in. (H) 0.6 m (L) x 0.7 m (D) x 1 m (H)

Related recommendations

Falex-High Temperature Bearing
Brand：FALEX

Falex-Fretting Wear Test Machine
Brand：FALEX

Falex-Timken
Brand：FALEX